Solace Heating and Air provides spring maintenance for split HVAC units in Jackson, Tennessee. They inspect all system components and clean the condenser coil to ensure efficient operation and prevent potential issues.

Solace Heating and Air performed spring maintenance on an HVAC unit. They inspected wiring, capacitors, motors, and the capacitor. After confirming all parts were in good condition, they cleaned the unit and checked the Freon levels to ensure proper function.

Solace Heating and Air replaced a blown compressor in an HVAC unit. They tested the system to ensure the fan and compressor run properly and maintain cooling efficiency. This service took place in an unspecified location.

Solace Heating and Air performed maintenance on a newer HVAC unit. They inspected and cleaned all components, ensuring the system is fully prepared for the upcoming cooling season. This service supports reliable and efficient air conditioning operation. Location details were not specified.

Solace Heating and Air inspected a 2007 model air conditioning unit and identified a faulty condenser motor. They provided the customer in an unspecified location with an estimate for motor replacement and a separate estimate for replacing the entire system.

Solace Heating and Air cleaned the vent motor pressure area to remove wasp blockage caused by cold outdoor temperatures. After cleaning, they tested the unit to ensure proper operation and found no issues. This service was performed in the local area.

Solace Heating and Air diagnosed a faulty vent motor causing loud noise and pressure issues. After replacing the motor, the unit operated properly without any problems. This heating and air service ensures vent motors function correctly to maintain system performance. Location details are not specified.

Solace Heating and Air replaced a TXV on an Ameristar split gas system in Jackson, Tennessee, verifying the unit’s cooling efficiency and optimal operation to ensure reliable, cost-effective HVAC performance.

Solace Heating and Air installed a Trane high-efficiency gas package unit in Jackson, Tennessee. The unit operates efficiently, providing reliable heating and cooling for the property. This service ensures improved energy use and consistent indoor comfort.

Solace Heating and Air serviced an older Trane package heat pump in Jackson, Tennessee. They diagnosed a no-heat issue caused by a faulty outdoor TXV. The technician assessed the system and provided the customer with repair options.

Solace Heating and Air serviced an older Carrier HVAC unit by inspecting the compressor and capacitor. They replaced the faulty capacitor, restored proper function, and ensured the unit operated effectively. This HVAC repair service is available without a specified city or state location.

Solace Heating and Air inspected a 4-year-old Trane gas package system in Dyersburg, TN. They identified a disconnected yellow wire at the thermostat terminal and reconnected it, restoring the unit’s cooling function.

Solace Heating and Air performed spring maintenance on a 2016 high-efficiency Trane unit in Atlanta, GA. They inspected all components, including the capacitor and wiring. They cleaned the unit, checked the Freon level, and confirmed the system delivers cold air efficiently.

Solace Heating and Air inspected an air conditioning unit in Lansing, Michigan. They found the Freon level was two to three pounds low, reducing cooling efficiency. The technician provided a quote for a new unit to the customer.

Solace Heating and Air replaced outdoor coils on two commercial Samsung VRF units in Jackson, Tennessee. They pressure tested the systems to confirm there were no leaks. This service ensures the HVAC units operate efficiently and safely.

Solace Heating and Air diagnosed a no-cool issue on a Carrier split heat pump in Jackson, Tennessee, identifying a damaged coil restricting airflow. They provided detailed repair options to restore efficient cooling.

Solace Heating and Air repaired a blown 24V three-amp fuse, inspected system components, tightened all connections, and tested heating, cooling, and strip heat functions. The unit operated efficiently after service. This HVAC maintenance was performed in an unspecified location.

Solace Heating and Air replaced a rusty rainshield with a properly fitting one to protect ductwork from weather and animal damage. This service took place in Memphis, Tennessee, ensuring HVAC systems remain secure and functional.

Solace Heating and Air inspected a rooftop HVAC unit in a commercial building in Los Angeles, CA. They confirmed the system operates efficiently and provided an estimate for replacing return and supply air grills to maintain proper ventilation.

Solace Heating and Air diagnosed a faulty thermostatic expansion valve (TXV) that remained stuck open after testing. They identified this issue in the customer's HVAC unit and confirmed it by checking the superheat levels. This service ensures accurate HVAC system performance in the local area.

Solace Heating and Air replaced a customer-supplied wall heater in Boca Raton, Florida, conducted a thorough leak inspection with no leaks found, and tested the unit to confirm optimal operation, ensuring reliable indoor heating.

Solace Heating and Air serviced a heating unit in their local area by diagnosing a faulty sequencer that kept the heat running past the thermostat setting. After replacing the sequencer, the system operated properly and shut off as expected.

Solace Heating and Air replaced two relays and installed a customer-provided thermostat in an air handler system in Charlotte, North Carolina. After completing the replacements, technicians tested the system to confirm proper operation and efficiency.

Solace Heating and Air inspected a malfunctioning HVAC system in an unidentified location and found damage in the return duct. Technicians determined that the existing flex pipe had holes and recommended replacing it with hard pipe to restore proper airflow.

Solace Heating and Air inspected a damaged HVAC return and duct system in Greenville, South Carolina. The return line had collapsed and detached from beneath the house. The technician assessed the issue and prepared a quote for full replacement of the return and ductwork.

Solace Heating and Air installed a soft start on a new American Standard compressor unit. The upgrade reduced amp draw and improved overall system performance. This service ensures smoother startups and lowers strain on electrical components, contributing to longer equipment life. Location information was not available for this check-in.

Solace Heating and Air replaced an inducer motor relay on a Goodman gas package unit in Jackson, TN, ensuring reliable heating during winter by verifying system operation post-service.

Solace Heating and Air installed a Samsung 12,000 BTU mini split in Jackson, Tennessee. The system is operating correctly and delivering consistent performance. This installation supports efficient temperature control.

Solace Heating and Air replaced a faulty blower motor on a Rheem split system in Jackson, Tennessee, restoring optimal airflow and cooling performance. The technician verified proper operation post-repair, ensuring homeowner comfort during seasonal temperature changes.

A technician in Jackson, Tennessee inspected a non-working Rheem HVAC unit and identified a locked-up blower motor. The technician presented repair options to the customer to restore system function.

Solace Heating and Air diagnosed a faulty touchscreen on a Trane thermostat in Jackson, Tennessee. They offered several replacement options, and installed the customer's chosen thermostat promptly.

A technician in Jackson, Tennessee inspected a Goodman gas package system that was not producing heat. They identified a dirty flame sensor as the problem, cleaned the sensor, and confirmed that the system was heating correctly.

Solace Heating and Air diagnosed two Samsung VRF units in Jackson, Tennessee, detecting leaking condenser coils and offering tailored repair solutions to restore system efficiency.

A technician in Jackson, Tennessee inspected an older Amana gas package system that had no heat. The control board showed signs of failure. The technician informed the customer and recommended replacing the board to restore proper system function.

A technician inspected an Airease gas furnace in McKenzie, Tennessee that was not producing heat. The issue was traced to a locked gas meter, and the cause was explained to the customer.

Solace Heating and Air replaced a failed inducer motor, gas valve, and control board on a Goodman gas furnace in Jackson, Tennessee, verifying proper operation to ensure reliable heating during winter months.

A technician in Linden, Tennessee inspected a York high-efficiency condensing furnace due to a strong odor. The source was traced to the condensate drain. To resolve the issue, the technician installed a drain trap to separate the furnace from the drain line.

A technician inspected a 2007 Lennox system with no heat in Moscow, Tennessee. The diagnosis showed a failed condenser fan motor, contactor, and capacitor. The customer deferred repairs for a future visit.

Solace Heating and Air replaced damaged thermostats on hanging heaters in Memphis, Tennessee after a power surge. The technicians restored heating function and performed carbon monoxide tests to ensure homeowner safety.

Solace Heating and Air completed a combustion analysis on a propane gas package unit in Jackson, Tennessee. The technician confirmed the unit operates efficiently and burns cleanly, ensuring proper fuel use and system performance.

Solace Heating and Air inspected an Ameristar gas package system in Brownsville, Tennessee. Technicians found the unit operational but detected a weak blower motor capacitor. They replaced the capacitor to maintain proper heating function.

Solace Heating and Air repaired a 20-year-old American Standard gas furnace in Brownsville, Tennessee. The technician replaced a faulty inducer motor and a weak blower capacitor. The system was tested and confirmed to be heating properly after the repair.

A technician repaired a Samsung Hylex HVAC system experiencing no heat in Dyersburg, Tennessee. The unit was undercharged on refrigerant. The technician restored proper refrigerant levels to allow the system to heat effectively.

A technician in Henderson, Tennessee inspected a PTAC unit that was blowing cold air. They discovered a burnt control board near the heating element relay. Since replacement parts were unavailable, they provided the customer with replacement options.

Solace Heating and Air serviced gas logs in Jackson, Tennessee. The team cleaned the thermocouple, repaired a damaged thermostat wire, and confirmed proper thermocouple voltage to prepare for upcoming cold weather.

Solace Heating and Air diagnosed a grounded compressor in a York Package Heat Pump system in Jackson, TN, advising the homeowner on repair costs and replacement benefits during January service.

A technician in Jackson, Tennessee inspected a Nordyne gas furnace that was not producing heat. They identified a weak blower capacitor and a low-reading flame sensor. The technician explained the issues and presented the customer with repair options.

A technician in Jackson, Tennessee inspected two gas package HVAC systems with separate issues. The inspection included heat exchangers, blower motors, coil condition, and electronics. The technician completed a detailed assessment of both systems to determine their operational status.

A technician in Jackson, Tennessee inspected a Goodman gas package system before a cold spell. The service included checking the heat exchanger, blower, and inducer assembly. All components were in good working condition, ensuring the system was ready for consistent heating performance during colder temperatures.

Solace Heating and Air completed heating maintenance on two gas systems in Jackson, Tennessee. Technicians inspected heat exchangers, blowers, igniters, flame sensors, and related parts to confirm proper operation for the heating season.

Solace Heating and Air conducted thorough heating maintenance on two systems in Jackson, Tennessee, inspecting motors, capacitors, and coils to ensure optimal condition and reliable performance throughout the winter season.

Solace Heating and Air inspected a heating system in Dayton, Ohio. Technicians identified a failed gas valve and control board. The gas valve shorted and caused damage to the board. Repairs addressed both components to restore system function.

Solace Heating and Air adjusted a flue pipe in Jackson, Tennessee to ensure it remained one inch from the wall. The technician inspected the heating system and confirmed it was operating without additional issues.

Solace Heating and Air installed an Ameristar gas package system in Jackson, TN, verifying correct operation with performance tests to ensure reliable heating efficiency.

Solace Heating and Air inspected a heating unit in Athens, Georgia. The technician found gas residue on the flame sensor and cleaned it. After the cleaning, the technician confirmed the system was operating efficiently.

Solace Heating and Air inspected an HVAC system in Milton, Delaware and identified a failed compressor, inoperative heat pump, and faulty heat strips. Technicians assessed the issues and confirmed the unit could not operate due to multiple critical component failures.

Solace Heating and Air replaced a failed control board under warranty in a residential HVAC unit. After installation, technicians tested the system to confirm proper operation. All functions performed as expected following the repair. Location information is not available for this service.

A technician from Solace Heating and Air inspected a heating unit in Houston, Texas, and identified a clogged air filter that was triggering the high limit switch. The customer chose to replace the filter later the same day. The unit required no further service during the visit.

Solace Heating and Air completed a system maintenance service on a split heat pump in Clarksville, Tennessee. The technician inspected and serviced one unit to maintain efficient heating and cooling performance. Routine maintenance helps prevent system issues and supports long-term operation.

Solace Heating and Air replaced a blower motor and blower motor control board in Jackson, Tennessee. Technicians completed the repair and confirmed the equipment is working correctly. This service restored full function to the HVAC system.

Solace Heating and Air cleaned a dirty flame sensor on a heating unit in Dallas, Texas. The technician inspected the system and confirmed all functions operated efficiently after service.

Solace Heating and Air performed winter maintenance on two Goodman gas units atop a roof in Jackson, Tennessee. Technicians verified optimal heating output, conducted comprehensive inspections, and replaced air filters to ensure efficiency.

Solace Heating and Air replaced a faulty high limit switch on a two-month-old Ameristar unit in Sacramento, California. The part was under warranty and the repair restored proper system function.

Solace Heating and Air completed winter maintenance on a new heating unit in Greensboro, North Carolina. Technicians inspected all heating components and filters. The system is functioning properly after the service.

Solace Heating and Air completed winter maintenance on three HVAC units in [City, State]. Technicians inspected heating components, replaced filters, and identified a low capacitor on one unit. All other systems operated within normal ranges.

Solace Heating and Air diagnosed a faulty thermostat in Visalia, California. The unit's adjustment button was stuck, preventing temperature changes. The technician identified the issue and confirmed the thermostat was not responding to input commands.

Solace Heating and Air inspected a gas log system in Greenville, South Carolina, and identified a gas valve leak. The team determined that replacement of the entire gas log set was necessary due to the unavailability of compatible gas valve parts.

Technicians replaced a faulty control board and igniter in a Trane HVAC unit. After installation, they tested the system to confirm proper operation. This heating repair service was completed by Solace Heating and Air in Amarillo, Texas.

A technician inspected an older HVAC unit in need of R-22 refrigerant and identified a system leak. After checking potential causes, the customer requested an estimate for a new unit. This HVAC assessment and replacement estimate took place in Decatur, Alabama.

No specific service details or location information were provided in the check-in data. Please supply a description of the service performed and a valid city and state for accurate content creation.

Solace Heating and Air replaced a failed blower motor on an older Trane unit in Florence, Alabama. The team installed the new motor, tested system function, and cleaned the blower wheel to improve airflow and performance.

Solace Heating and Air completed a winter tune-up on a newer Trane unit in Garland, Texas. Technicians inspected all components, confirmed proper operation, and ensured the system was clean and ready for cold weather performance.

Solace Heating and Air replaced a gas valve on a new American Standard unit in Philadelphia, Pennsylvania. They reset the pressure to 3.3 and verified that the heating system operated correctly after testing. The system showed no further issues at the time of service.

A technician inspected a new gas floor heater in Lake Havasu City, Arizona, but could not complete testing because the connected propane tank was empty. Service will resume once the propane supply is restored.

Solace Heating and Air replaced the sensor harness and control board on a Samsung HVAC unit in Jackson, Tennessee. Post-installation tests confirmed efficient operation, ensuring reliable climate control for local homeowners.

A technician inspected a new Rheem gas unit in Birmingham, Alabama, due to a rattling noise. After checking the unit and ductwork, they traced the issue to a return grill inside. They applied insulation to the grill, which resolved the vibration problem effectively.

Solace Heating and Air provided an estimate to maintain all heating and air conditioning systems at the property. This service includes evaluating equipment condition and outlining steps for ongoing system care. Location details were not specified.

Solace Heating and Air replaced a ceiling return air filter for a Trane split system in Bentonville, Arkansas. This service was completed as part of a scheduled maintenance agreement to support consistent airflow and system reliability.

Solace Heating and Air completed a winter heating tune-up on a 2020 Trane split heat pump in Fort Smith, Arkansas. Technicians checked motor performance, confirmed refrigerant pressures were correct, and ensured the defrost cycle functioned properly. This maintenance helps maintain system reliability during colder months.

Solace Heating and Air installed a new floor furnace in Fresno, California. Technicians added new venting and thermostat wires. They tested the system and confirmed the furnace functions correctly.

Solace Heating and Air repaired a Rheem gas furnace in Greenville, South Carolina. A damaged pressure tube caused heating failure. Technicians identified rodent damage to the tubing between the inducer motor and pressure switch. They replaced the tubing and restored full operation of the furnace.

Solace Heating and Air replaced a failing blower motor on a 2014 Trane gas package system that had no heat. This heating repair service was completed in Jackson, Tennessee.

Solace Heating and Air completed a fall maintenance check on a 2024 American Standard gas package system in Jackson, Tennessee. The technician confirmed that all components of the system are operating correctly. This service helps maintain energy efficiency and consistent performance through seasonal changes.

A technician in Milan, Tennessee replaced a faulty limit switch on a 2018 AmeriStar gas package system. After completing the replacement, the technician confirmed that the entire heating system was operating correctly.

Solace Heating and Air replaced a recalled control board under warranty in Jackson, Tennessee. The replacement included both parts and labor at no additional cost. The service ensured the HVAC system continued to operate reliably and safely.

A technician diagnosed a no-heat issue on a Trane gas furnace and identified a faulty hot surface igniter. The team replaced the igniter and confirmed the furnace is now heating correctly. This service was completed by Solace Heating and Air. Location data was not provided for this job.

Solace Heating and Air repaired a non-working Trane package system in an older unit in [City, State unavailable]. The technician identified a faulty inducer motor and a rusted burner assembly, then explained available repair options to restore heat and system function.

Solace Heating and Air inspected electrical connections and measured component amperage in Memphis, Tennessee. Technicians confirmed all values met specifications. They also checked safety controls and the heat exchanger to ensure safe furnace operation. The system is ready for the heating season.

Solace Heating and Air completed fall heating maintenance on a Carrier gas furnace in October 2025. The technician inspected the heat exchanger, evaporator coil, blower assembly, and burners to confirm the system was operating correctly and ready for the heating season. Location details were not provided.

Solace Heating and Air completed fall heating maintenance on a Trane natural gas furnace in Livonia, Michigan. The technician inspected the coils, heat exchanger, blower motor, inducer motor, and burner assembly. The service confirmed the system is heating correctly and safely for the season.

A technician repaired a Luxaire gas package unit in Florence, South Carolina. The unit was not cooling due to a swollen dual capacitor. The technician replaced the faulty capacitor and confirmed the rest of the system was operating correctly.

Solace Heating and Air completed fall heating maintenance on two split heat pump systems in Georgia. The technician inspected refrigerant coils, checked refrigerant pressures, and tested capacitors and motor amp draws to ensure proper operation ahead of cooler weather.

Solace Heating and Air completed fall heating maintenance on an Ameristar gas package system. The technician inspected the burners, inducer motor, igniter, and heat exchanger to ensure they were functioning properly. This service helps maintain system efficiency and supports reliable heating performance through the colder months. Location details were not provided.

Solace Heating and Air completed fall heating maintenance on a split heat pump and a gas package system in Georgia. Technicians cleaned coils, blower assemblies, inducer ports, and sensors to prepare both units for the heating season.

Solace Heating and Air completed fall heating maintenance on a Trane gas package system in [City], [State]. The technician inspected the unit, found corrosion on the burner assembly, discussed repair options, and confirmed the system works properly for winter use.

Solace Heating and Air completed fall maintenance on a Trane gas package system in [City], [State]. Technicians inspected the heat exchanger, blower wheel, evaporator, and heating components. They confirmed the system functions correctly and is prepared for winter use.

A technician inspected a Rheem gas package unit and found a rusted inducer motor causing a no-heat issue. The technician explained the problem and discussed repair options with the customer in Fort Smith, Arkansas.

Solace Heating and Air inspected a natural gas fireplace in Oklahoma City, Oklahoma. The technician checked that the venting and oxygen depletion sensor met code requirements. They cleaned the thermocouple and confirmed the fireplace operated correctly.

Solace Heating and Air completed fall maintenance on a Trane gas furnace in Conyers, Georgia. The technician cleaned the air filter, evaporator, and blower wheel. They also tested the inducer motor, gas valve, and burners, and inspected the heat exchanger for proper function and safety.

Solace Heating and Air completed fall heating maintenance on an older Trane package heat pump system in North Carolina. The technician inspected motor operation, checked refrigerant pressures, confirmed proper defrost cycling, and verified that the heat strips were functioning correctly.

Solace Heating and Air completed fall heating maintenance in Greensboro, North Carolina. The service included inspecting a gas package unit and a split heat pump system. Technicians checked motors, heat exchangers, heating strips, and the burner assembly to confirm both systems operate properly for the winter season.

A technician from Solace Heating and Air inspected a York split heat pump in Jacksonville, Florida. The system was not cooling due to a short that caused the low voltage fuse to blow. The technician diagnosed the issue and presented repair options to the customer.

Solace Heating and Air completed fall maintenance on a Nordyne air handler in Madison, Alabama. The technician inspected heat strip wiring, confirmed amp levels were correct, and identified a blower motor drawing excess current. Repair options were reviewed with the client to address the issue.

Solace Heating and Air completed fall maintenance on a Bryant gas package system in North Carolina. Technicians cleaned rusted burners that were preventing ignition. They inspected the heat exchanger, inducer motor, and related components to confirm proper function before winter.

A technician completed fall heating maintenance on a Trane gas furnace in Solace, North Carolina. The service included cleaning the flame sensor and pressure port, inspecting the heat exchanger, and confirming that all motors operate correctly. The furnace is now prepared for the upcoming heating season.

Solace Heating and Air completed a fall tuneup in Denton, Texas on a gas split system and a gas package system. The technician cleaned flame sensors, checked safety switches, confirmed motor operation, and inspected heat exchangers for proper function.

Solace Heating and Air performed seasonal heating maintenance on a gas package system in Spring Hill, Tennessee. Technicians inspected all components and confirmed the unit is heating the home correctly. This service helps maintain system performance and ensures reliable operation during colder months.

Solace Heating and Air completed fall maintenance on a Trane gas package system in North Carolina. Technicians removed a wasp nest from the inducer motor, inspected all heating components, and confirmed the unit operates correctly. The system is now ready for the colder season and functioning as expected.

A technician from Solace Heating and Air replaced a faulty blower motor on a Carrier split heat pump in North Carolina. They confirmed the unit is operating correctly and cooling efficiently after the repair.

Solace Heating and Air responded to a no-cool issue on a 2004 Rheem gas package system. Technicians identified a weak compressor start capacitor, replaced it, and confirmed the system now functions correctly. Location details were not provided.

Solace Heating and Air replaced a recalled control board on an American Standard gas package unit in Denton, Texas. The team confirmed the unit now operates correctly with no remaining issues.

Solace Heating and Air completed heating maintenance on a Trane dual fuel package system in Monroe, North Carolina. The technician checked the heat pump, defrost function, and gas backup operation. The service included identifying and reporting any needed repairs to the homeowner.

A technician in Jackson, Tennessee replaced a damaged blower motor and furnace control board on a York gas furnace. The repair restored full heating system function and ensured proper airflow and safety. System performance was tested and confirmed after installation.

A technician from Solace Heating and Air responded to a no cooling issue in a residential HVAC system. The unit was low on refrigerant. The technician identified a leak in the TXV and placed an order for a replacement TXV to restore proper system function. Location data was not provided.

Solace Heating and Air repaired an advanced HVAC system in Charlotte, North Carolina. Technicians located and replaced damaged components caused by a short in the staging boards. They synchronized all four operational stages to restore proper system function across multiple days of service.